OpDAT FAST Faser-Guide SC

15080020FGE-E

• Fiber insertion guide for field-terminable fiber optic connectors SC (OpDAT FAST^TM Hybrid and OpDAT FAST^TM )
• Used for exact marking of the settling dimensions on the wire and for safe and easy insertion of the fibre into the connector.
• Colour: blue

OpDAT FAST Faser-Guide LC

15080020FGJ-E

• Fiber insertion guide for field-terminable fiber optic connectors LC (OpDAT FAST^TM Hybrid and OpDAT FAST^TM )
• Used for exact marking of the settling dimensions on the wire and for safe and easy insertion of the fibre into the connector.
• Colour: blue

OpDAT cable guide for OpDAT 4 UP

150810-I

• for combination with the fiber optic wall outlet OpDAT 4 UP
• cable guide for fiber optic wall outlet to maintain minimum bending radii for fiber optic cables to TIA/EIA 568A (> 30 mm)
• in conjunction with mounting bracket for wall outlets (see accessory)
• cable feed with cable tie tension relief

ENW-E12, 230 V AC

11030805

The level sensor monitors filling levels or leakage of all conductive, noncombustible media. The trigger can be adjusted by means of a proportional potentiometer. As monitor, the device works with an electrode (EO) and the ground connection (EM), e.g. for minimum and maximum levels, to protect submersible pumps from overflowing or running dry. If the surface of the fluid is subject to disturbance, we recommend another electrode (EU). As two-level controller, the device controls pumps or valves for automatically filling and emptying containers by means of the EO and EU electrodes and the EM ground connection. A container wall, being conductive to the medium, can also be used as ground connection. With 2 electrodes connected the contacts B2 and B3 must be connected with a bridge! Variant: 230 V AC

ENW-E12, 24 V AC

11030810

The level sensor monitors filling levels or leakage of all conductive, noncombustible media. The trigger can be adjusted by means of a proportional potentiometer. As monitor, the device works with an electrode (EO) and the ground connection (EM), e.g. for minimum and maximum levels, to protect submersible pumps from overflowing or running dry. If the surface of the fluid is subject to disturbance, we recommend another electrode (EU). As two-level controller, the device controls pumps or valves for automatically filling and emptying containers by means of the EO and EU electrodes and the EM ground connection. A container wall, being conductive to the medium, can also be used as ground connection. With 2 electrodes connected the contacts B2 and B3 must be connected with a bridge! Variant: 24 V AC

OpDAT FAST^TM Hybrid connector kit SC PC OM3/OM4
10 pieces for buffered fibres

1509MAEO0010-E

• Field-attachable fiber optic connector for multimode technology
• With hybrid technology: refractive index gel plus Opto-Elast guarantee very good and constant optical values.
• No polishing, no gluing during assembly on site.
• Simple, easy to learn, fast and cost-effective installation in less than two minutes.
• Available with connector types LC and SC.
• Lug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• Plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• The plug can be assembled up to three times.
• Every plug has a serial number, so that traceability is possible at any time.
• Included in the scope of delivery depending on the variant:
• A maintenance-free cutting device (cleaver), designed for a diagonal cut. The cleaver can be used up to 200 times.
• A cable assembly kit for easy cable assembly
• A fiber guide for easy insertion of the fiber into the connector
• Fields of application: for FTTH and FITH connections, repairs in the field and in areas which are difficult to access or limited in space and for direct mounting to components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC PC OM3/OM4
20 pieces for buffered fibres incl. tool

1509MAEO002C-E

• Field-attachable fiber optic connector for multimode technology
• With hybrid technology: refractive index gel plus Opto-Elast guarantee very good and constant optical values.
• No polishing, no gluing during assembly on site.
• Simple, easy to learn, fast and cost-effective installation in less than two minutes.
• Available with connector types LC and SC.
• Lug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• Plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• The plug can be assembled up to three times.
• Every plug has a serial number, so that traceability is possible at any time.
• Included in the scope of delivery depending on the variant:
• A maintenance-free cutting device (cleaver), designed for a diagonal cut. The cleaver can be used up to 200 times.
• A cable assembly kit for easy cable assembly
• A fiber guide for easy insertion of the fiber into the connector
• Fields of application: for FTTH and FITH connections, repairs in the field and in areas which are difficult to access or limited in space and for direct mounting to components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC PC OM3/OM4
100 pieces for buffered fibres incl. tool

1509MAEO010C-E

• Field-attachable fiber optic connector for multimode technology
• With hybrid technology: refractive index gel plus Opto-Elast guarantee very good and constant optical values.
• No polishing, no gluing during assembly on site.
• Simple, easy to learn, fast and cost-effective installation in less than two minutes.
• Available with connector types LC and SC.
• Lug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• Plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• The plug can be assembled up to three times.
• Every plug has a serial number, so that traceability is possible at any time.
• Included in the scope of delivery depending on the variant:
• A maintenance-free cutting device (cleaver), designed for a diagonal cut. The cleaver can be used up to 200 times.
• A cable assembly kit for easy cable assembly
• A fiber guide for easy insertion of the fiber into the connector
• Fields of application: for FTTH and FITH connections, repairs in the field and in areas which are difficult to access or limited in space and for direct mounting to components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC PC OM3/OM4
10 pieces for buffered fibres

1509MAJO0010-E

• Field-attachable fiber optic connector for multimode technology
• With hybrid technology: refractive index gel plus Opto-Elast guarantee very good and constant optical values.
• No polishing, no gluing during assembly on site.
• Simple, easy to learn, fast and cost-effective installation in less than two minutes.
• Available with connector types LC and SC.
• Lug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• Plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• The plug can be assembled up to three times.
• Every plug has a serial number, so that traceability is possible at any time.
• Included in the scope of delivery depending on the variant:
• A maintenance-free cutting device (cleaver), designed for a diagonal cut. The cleaver can be used up to 200 times.
• A cable assembly kit for easy cable assembly
• A fiber guide for easy insertion of the fiber into the connector
• Fields of application: for FTTH and FITH connections, repairs in the field and in areas which are difficult to access or limited in space and for direct mounting to components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC PC OM3/OM4
20 pieces for buffered fibres incl. tool

1509MAJO002C-E

• Field-attachable fiber optic connector for multimode technology
• With hybrid technology: refractive index gel plus Opto-Elast guarantee very good and constant optical values.
• No polishing, no gluing during assembly on site.
• Simple, easy to learn, fast and cost-effective installation in less than two minutes.
• Available with connector types LC and SC.
• Lug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• Plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• The plug can be assembled up to three times.
• Every plug has a serial number, so that traceability is possible at any time.
• Included in the scope of delivery depending on the variant:
• A maintenance-free cutting device (cleaver), designed for a diagonal cut. The cleaver can be used up to 200 times.
• A cable assembly kit for easy cable assembly
• A fiber guide for easy insertion of the fiber into the connector
• Fields of application: for FTTH and FITH connections, repairs in the field and in areas which are difficult to access or limited in space and for direct mounting to components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC PC OM3/OM4
100 pieces for buffered fibres incl. tool

1509MAJO010C-E

• Field-attachable fiber optic connector for multimode technology
• With hybrid technology: refractive index gel plus Opto-Elast guarantee very good and constant optical values.
• No polishing, no gluing during assembly on site.
• Simple, easy to learn, fast and cost-effective installation in less than two minutes.
• Available with connector types LC and SC.
• Lug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• Plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• The plug can be assembled up to three times.
• Every plug has a serial number, so that traceability is possible at any time.
• Included in the scope of delivery depending on the variant:
• A maintenance-free cutting device (cleaver), designed for a diagonal cut. The cleaver can be used up to 200 times.
• A cable assembly kit for easy cable assembly
• A fiber guide for easy insertion of the fiber into the connector
• Fields of application: for FTTH and FITH connections, repairs in the field and in areas which are difficult to access or limited in space and for direct mounting to components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC UPC OS2
10 pieces for buffered fibres

1509QAEO0010-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC UPC OS2
20 pieces for buffered fibres incl. tool

1509QAEO002C-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC UPC OS2
100 pieces for buffered fibres incl. tool

1509QAEO010C-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC UPC OS2
10 pieces for buffered fibres

1509QAJO0010-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC UPC OS2
20 pieces for buffered fibres incl. tool

1509QAJO002C-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC UPC OS2
100 pieces for buffered fibres incl. tool

1509QAJO010C-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC APC OS2
10 pieces for buffered fibres

1509QAEA0010-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC APC OS2
20 pieces for buffered fibres incl. tool

1509QAEA002C-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC APC OS2
100 pieces for buffered fibres incl. tool

1509QAEA010C-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC APC OS2
10 pieces for buffered fibres

1509QAJA0010-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC APC OS2
20 pieces for buffered fibres incl. tool

1509QAJA002C-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit LC APC OS2
100 pieces for buffered fibres incl. tool

1509QAJA010C-E

• Field-attachable fiber optic connector for single-mode technology
• with hybrid technology: refractive index gel plus opto-elastomer guarantee very good and constant optical values
• no polishing, no gluing during assembly on site
• simple, easy to learn, fast and cost-effective installation in less than two minutes
• Available with connector types LC and SC for singlemode (UPC and APC)
• plug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• the plug can be assembled up to three times
• every plug has a serial number, so that traceability is possible at any time
• Included in the scope of delivery depending on the variant:
• a maintenance-free separator (Cleaver). It provides an oblique cut so that high return loss values are achieved. The Cleaver can be used up to 200 times.
• a cable assembly kit for easy cable assembly
• a fiber guide for easy insertion of the fiber into the connector
• fields of application:
• for FTTH and FITH connections, repairs in the field, in areas which are difficult to access or limited in space and for direct mounting on components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide

OpDAT FAST^TM Hybrid connector kit SC PC OM3/OM4
10 pieces for cables

1509MKEO0010-E

• Field-attachable fiber optic connector for multimode technology
• With hybrid technology: refractive index gel plus Opto-Elast guarantee very good and constant optical values.
• No polishing, no gluing during assembly on site.
• Simple, easy to learn, fast and cost-effective installation in less than two minutes.
• Available with connector types LC and SC.
• Lug kits for FO fibers with Ø 0.25 and Ø 0.9 mm
• Plug kits for fibre optic cables with Ø 2.0 and Ø 3.0 mm
• The plug can be assembled up to three times.
• Every plug has a serial number, so that traceability is possible at any time.
• Included in the scope of delivery depending on the variant:
• A maintenance-free cutting device (cleaver), designed for a diagonal cut. The cleaver can be used up to 200 times.
• A cable assembly kit for easy cable assembly
• A fiber guide for easy insertion of the fiber into the connector
• Fields of application: for FTTH and FITH connections, repairs in the field and in areas which are difficult to access or limited in space and for direct mounting to components
• Versions for fibers: 10 pieces without tools / 20 or 100 pieces with Cleaver and fibre guide
• Variants for cables: 10 pieces without tools / 20 or 100 pieces with Cleaver, cable assembly set and fibre guide